 Search the Knowledgebase |
 Browse by Category |
|
|
|
| View Articles by Category |
|
There are no sub categories
|
Z-Vent Dimensions
|
There were 19 articles found in this category:
 Horizontal Condensate Drain
- Z-VENT Appliance Adapter with Condensate Drain and Backflow Preventer
Z-Vent Part # 2SVBFDPA04 10 3/4 inches high Appliance Adapter, Condensate Drain and Backflow Prevention Built into one piece. Mounts on top of the Appliance in a Vertical position. Condensate Starter Hose shown in photo is sold se ...
- Hi-Temp RTV Sealant
Temperature Rating: -62 to +500 Degrees F. For use inside the Storm Collar before clamping, minimizes rain water from trickling down the outside of the pipe. Also used on the back of a flush mounted Termination to keep moisture from entering behind the Termination. Not to be used when joining ...
- Firestop Support
- Condensate Drain:Vertical In-Line
* Dimensions: 3 inch diameter pipe = 8 inches high 4 inch diameter pipe = 8 inches high * Suggested placement is closest to the exhaust on the heater, normally above the appliance adapter. * Inner Gasketed female and non-gasketed male * Hi-Temp starter Condensate H ...
- Universal Appliance Adapter
Gasketed on both ends ( Female/Female) The Bosch Tankless models 2700, 250, 2400 and 635 series do not require an Appliance Adapter but does require our Z-Vent 3 inch diameter vent pipe. The Bosch Tankless model 250 does require our 4 inch diameter Z-Vent pipe as well as an Appliance Adapter. ...
- Termination Tee
- Termination Hood
- Termination Box
- Roof Flashings
- Rain Cap
Installations also require the use of a Storm Collar in addition to the Rain Cap.
- Paloma PTG-42 & Rheem RTG-42 Appliance Adapter
Paloma PTG-42 & Rheem RTG-42 Appliance Adapter
- Extended Wall Thimble
The Wall Thimble in 3 Inch diameter requires a 7 inch round hole for installation and a 4 inch diameter thimble requires a 8 inch round hole for installation.This will provide the correct clearance to combustibles.
- Appliance Adapter with Backlow Prevention
- Adjustable Length
* Update August 2010: 3" diameter is adjustable from 4.5" to 10.5" 4" diameter is adjustable from 4.5" to 16.0"
- 45 Degree Elbow
* Z-Vent 45 degree and 90 degree elbows are non-adjustable, rigid elbows. * Inner gasketed female and non-gasketed male * In many cases, a 45 degree elbow will have the value of 2.5 feet against your maximim length of pipe run. Check your manufacturers installation manual for their venting req ...
- Wall Thimble
The Wall Thimble in 3 Inch diameter requires a 7 inch round hole for installation and a 4 inch diameter thimble requires a 8 inch round hole for installation.This will provide the correct clearance to combustibles.
- Vertical Condensate Drain Tee
- 90 Degree Elbow
*The Z-Vent 90 degree and 45 degree elbows are all non-adjustable,rigid elbows. * Inner Gasket on the female end, non-gasketed male * In many cases, a 90 degree elbow will have the value of 5 feet against your maximim length of pipe run.Also, some appliance manufacturers limit the number of elb ...
|
we ship z-flex chimney liners and z-flex stainless steel venting -al29 4c- and to all 50 states. order by 1:30pm central and it ships today!
