| Search Results for "direct-temp venting instructions" |
|
There were 21 articles found for your query:
|
(Page 1 of 2)
«« |
Prev |
1 |
2 |
Next |
»»
|
 Paloma Tankless Install Manual
Listed below in a PDF is the venting requirements for the Paloma PTG42 and the PTG74. When ordering your vent pipe,consider including either the horizontal or vertical condensate drain. Our Z-Vent P...
- Massachusetts Bulletin
...tallation Instructions
Following are additional instructions required by The Massachusetts Board o... (7) feet above finished grade in the area of the venting, including but not limited to decks and po...
- What is Z-Vent ?
...brand that is cutable *UL1738 listed for Category I, II,III and IV heating equipment. * Used for venting appliances with positive pressure of 8" of water column or less.Tankless water heaters ...
- Why can't I use Double wall B-Vent on my Tankless or Boiler ?
...nual for your appliance will list the correct UL listing and/or a short description of the required venting.
- Should I use screws,sealant or tape to secure the Z-vent connections ?
NO, sealant,screws or tape should not be used to secure any connections on Z-vent pipe. The hi-temp gasketed end of the pipe is enough for a tight connection. Using screws will cause a leak of de...
- Can I Vent into my existing chimney ?
No, your exhaust pipe has to be vented all the way to the outside of the house or building. Venting to the chimney does not allow the chimney to draft the flue gas, resulting in carbon monoxide ...
- Will a stainless steel chimney liner be OK for venting a Tankless?
No, a chimney liner (no matter the material) is not acceptable for venting a Tankless water heater. A flexible chimney liner is not a UL approved method and again, is unsafe. Many people think th...
- Can I Common Vent another Appliance with my Tankless ?
No,the Tankless water heater venting has to have its own separate vent pipe. Common venting with another appliance is against code and you tankless will not perform under that condition.
- Can I use Z-Vent pipe with another brand of pipe ?
...rs pipe. The connections are all different between manufacturers pipe so you would not have a safe venting system.
- Do I need Z-Vent Double-Wall for my Tankless Venting ?
Most Tankless manufacturers only require our Z-Vent AL29-4C single wall stainless steel.However, it's always best to check with your local building inspector because your local code may require doube ...
- How do I return an item ?
...our purchase. Please read your installation manual or check for local code requirements for correct venting of your appliance. For example, a local code may require a double-wall stainless steel pipe ...
- Takagi Install Manuals
..." section of the manual. *Please note that each model has parameters as to the minimum and maximum venting length and number of elbows that can be used. Takagi suggests the use of a Backflow part # ...
- Bosch Install Manuals
..." section of the manual. *Please note that each model has parameters as to the minimum and maximum venting length and number of elbows that can be used. * The use of an additional condensate drain i...
- Noritz Installation Manuals
...eter vent pipe and Appliance adapter. * Each model has specific parameters for minimum and maximum venting length and the total number of elbows that can be used. TheZ-Vent Appliance Adapter for Nor...
- Bosch Condensate Service Bulletin
* The use of an additional condensate drain is required for the Bosch 250,635, 2400 and 2700 series. (PDF attachment below) Cinnabar Equipment stocks 2 options for this requirement, a Horizontal ...
- What is Class A Chimney Pipe ?
Selkirk Metalbestos Type HT Chimney is ideal for venting residential heating appliances burning wood,#2 oil,natural and LP gas. It has been specifically designed for today's modern,hi-efficien...
- Tankless Horizontal & Vertical Starter Kit
... pipe above the roof so additional pipe may be needed. A Condensate drain is suggested for vertical venting. Vent kits for Tankless water heaters may be purchased here.
- 90 Degree Elbow
...limit the number of elbows that can be used. Check your manufacturers installation manual for their venting requirements.
- 45 Degree Elbow
...eet against your maximim length of pipe run. Check your manufacturers installation manual for their venting requirements.
- Condensate Drain:Vertical In-Line
* Dimensions: 3 inch diameter pipe = 8 inches high 4 inch diameter pipe = 8 inches high * Suggested placement is closest to the exhaust on the heater, normally above th...
(Page 1 of 2)
«« |
Prev |
1 |
2 |
Next |
»»
|
we ship z-flex chimney liners and z-flex stainless steel venting -al29 4c- and to all 50 states. order by 1:30pm central and it ships today!
Search the Knowledgebase
Browse by Category